Construction and Home Improvemen

Laminate hardwood flooring is very versatile flooring that gives the appearance of having hardwood flooring without the expensive price tag. Although laminate flooring does look like hardwood, it is not made of solid wood. It is called engineered hardwood because it is made from several materials bonded together under extremely high pressure. It is easy to lay and care for and when you step on it, it is almost like you are floating. This is why laminate hardwood flooring is also called a floating floor.

You can lea how to lay laminate flooring very quickly. Once you see the first few planks of the flooring going together, you can complete the rest of the job on your own. You can install Quick Step laminate flooring on just about any room of your home. However, it is not recommended for use in bathrooms, mudrooms or any other room where there could be an excess of moisture. The extra water could damage the flooring meaning you would have to remove and replace one or two planks of the laminate flooring.

If you are looking at how easy it is to lea how to lay laminate flooring, you will also lea about the advantages of Quick Step laminate flooring. In contrast to solid hardwood, laminate hardwood flooring is about half the cost. It is easy to install and there is no finish or refinish to worry about. Installing laminate flooring doesn�t need any nails, but you can choose to glue it to the subfloor. Another advantage of laminate flooring is that you can lay it down on virtually any type of surface, except, of course, carpet. It is suitable for installing on top of concrete, wood or vinyl. All you have to do is to make sure the floor undeeath is level before you start to lay the planks.

When you ask the flooring retailer about how to lay laminate flooring, you will get several different instructions about how to prepare the floor beforehand. You do have to make sure the surfaces is free of any dust or small pieces of dirt that might work their way up through the laminate hardwood flooring. You also have to check to make sure the subfloor is soundproof and that it is level. Often people who have installed the Quick Step laminate flooring report that there are squeaks when they step on it. This is not the fault of the laminate flooring, but because the floor under it was not properly levelled before they started to lay the planks.

You do have to take extra care when you install laminate hardwood flooring over radiant heating. You have to read both the instructions for how to lay laminate flooring and the instructions regarding the radiant heat before you start. When you plan to lay laminate hardwood flooring in your home, you don�t have to open the packages until you are ready to start.

To find out more about Wood Flooring visit Peter's Website Wood Flooring Explained and find out about Installing Laminate Flooring and more, including Exotic Hardwood Floors, Wood Laminate Flooring, Refinishing Hardwood Floors and Bruce Hardwood Flooring.

Hanging a door these days is easier than its ever been. In the days before prehung doors, it took more tools and knowledge to hang a door than it does now.

Imagine getting a door slab, an unassembled door jamb, hinges and door hardware and having to do all the mortising, drilling, rabbeting on site.

No longer do you need an array of tools such as a drill, a mortising jig for hinges, strikes, and bolt plate. No jig for drilling the backset for the doorknob and bolt.

Nowadays all you need is a hammer and hard trim nails or a finish nail gun and some shims.

The first thing you need to do is check the opening you'll be hanging the door in for the correct size. It should be 2" bigger than the door size. Even though it's a rough opening it should be reasonably plumb and square.

If the opening was framed by someone else, you may want to break out your level and framing square and check this also. Drywallers sometimes believe the rough opening was meant for them and will let the drywall run into the opening. If this is the case use a drywall saw or sawzall to cut it back.

Once all the vitals have been checked your ready to hang a door. Prehung doors come assembled a couple different ways. They can be bought with trim already mitered and nailed on to one side and without trim. If there is no trim installed, I like to put it on before I put the door in the opening. The trim is installed on the hinge side.

Most doors open into a room and against a wall. When putting the door into the opening, try to put the door in the center of the opening. The door jamb should be able to move to the left and right in the opening. The gap between the door and jamb on the hinge side is usually about an 1/8" of an inch. This dictates the gap or space you should have all around the door. Move the door jamb to the left or right until you have that same space at the top. You then nail the trim on the top hinge side and the bottom hinge side. Then nail the strike side on the top making sure you still have an equal space. Nail off the rest of the hinge side with 3 or 4 more nails. The 2 nails already in the top are all I usually put in. Now nail the rest of the strike side starting at the top and working your way down, maintaining the same space as the top and hinge side.

Once the door is nailed into the opening on the inside, it's time to shim the door jamb. First, pull the door closed to make sure it hits the door stop evenly on the strike side. If it is hitting only at the top pull the hinge side toward you till it hits even. If it hits only at the bottom, push the hinge side jamb away from you till it hits evenly.

Once you get the jamb aligned put shims between the jamb and stud opening, being careful not to bow the jamb into the opening. If need be use a straight edge to keep it straight. I put shims behind every hinge and the strike and also at the top and bottom of the strike side. I nail these shims in with two nails, one on each side of the stop.

The next step is to apply the door casing to the outside of the door. Once this is done, your ready for the door hardware. If everything went right, the bolt should engage the strike plate and the door should fit snuggly against the stops.

(c) 2005 Mike Merisko www.sawkerfs.com

Article Source: http://www.articledashboard.com

About the Author: Mike Merisko has been a carpenter for 26 years. Most of those years were spent in the homebuilding and remodeling industries. He was also in business as a carpentry and general contractor. While that is his forte, he also has experience in bridge building, commercial construction, and exhibit building which is how he eas his living these days. You can browse through articles by him and others at his website www.sawkerfs.co